Magnesium sulphate recorded in multiple field trial areas
Released
Released
Announcement PDF
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
MAGNESIUM SULPHATE RECORDED IN MULTIPLE HOLES IN
MULTIPLE FIELD TRIAL AREAS
pH of MgS04 solution within target zone to leach rare earths into solution via ISR
Brazilian Critical Minerals Limited (ASX: BCM) (“BCM” or the “Company”) is pleased to announce that it
has successfully recorded the tracer reagent magnesium sulphate (MgS04) in multiple extraction holes
over field trial areas currently undergoing injection at the Ema project.
Highlights
•
Chemical changes in the solution now clearly show that magnesium sulphate has migrated from
the injection holes to the extraction holes in the field trial locations
•
pH levels have reduced significantly in the extraction solution with the addition of low
concentration MgS04 (0.5M) and are now at or below pH 4.0, the level required to leach rare
earths into solution via in-situ recovery (ISR)
•
Solution flows through the clay zone continue to exceed laboratory estimates and both the
injection and extraction wells are showing a steady rise in solution levels over time indicating
the basement rock is largely impermeable
•
Solutions potentially containing rare earths have now been extracted from the monitoring holes
and are enroute to the laboratory for analysis
Figure 1. pH measurements from 2 ISR field monitoring holes at location 1 (H1-8 and H1-9) versus
pH measurements taken from column laboratory testing over the same time period. Red circle
indicates levels at which rare earths become soluble.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Andrew Reid, Managing Director, commented:
“Over the past 10 days, we’ve successfully applied the same testing protocols to the Ema mineralisation
that delivered exceptional laboratory results throughout 2024 and early 2025. Encouragingly, the pilot
field trial has confirmed that permeability rates are not only consistent with lab data but, in many cases,
even better.
In recent days, we’ve also achieved a significant technical milestone—lowering the in-situ pH to levels
that demonstrate clear migration of magnesium sulphate through the clay layers to the extraction wells.
This is a critical step, as it indicates rare earth elements (REE’s) are now at a stage where they can be
ionically leached into solution.
This field trial which has been independently controlled and supervised by WSP Brazil further validates
our confidence in the simplicity and effectiveness of the in-situ recovery (ISR) process at Ema. The
mineralisation continues to demonstrate strong resilience, and the ease with which we’ve been able to
advance this low-impact extraction method is a key de-risking milestone.
We believe these developments represent a major step forward in unlocking the full potential of the
Ema project.”
Clay Permeability
A series of injection and extraction/monitoring holes (Figure 2.) were drilled at site location 2 in order
to be able to determine the time taken for solution to percolate through the clay horizon.
Figure 2. Injection and extraction/monitoring hole setup over a selective field trial area.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
For each of the monitoring holes, the solution level was measured several times daily. Figure 3 shows
the time taken for the initial solution to reach the monitoring holes;
• H2-10 – achieved breakthrough inside of 3hrs
• H2-11 – achieved breakthrough inside of 26hrs; and
• H2-12 – achieved breakthrough inside of 46hrs.
The time taken for solution to be recorded in the wells is in direct proportion to their distance from the
injection wells. This data suggests strong percolation of fluids through the clay horizon with the
information captured to be collated and used for hydrogeological modelling as part of the upcoming
bankable feasibility study and as part of our environmental permitting application which is directed by
CERN.
Figure 3. Solution levels measured daily and time taken for initial solution to reach monitoring holes.
Strong Bedrock Integrity Supports ISR Success
Monitoring hole data from the field trial (Figure 3) not only shows the initial time taken for solution to
reach these wells post injection, but also records the daily solution levels above the bottom of the hole
(recorded as depth 0). The consistent upward trend in solution levels observed across the first 100 hours
of injection indicates full in-situ saturation of the clays, retention of solution within the mineralised zone
and minimal solution loss—attributed to the impermeable nature of the underlying fresh bedrock.
Importantly, these trends have been observed consistently across the entire trial area to date (Figure 4),
confirming a key condition for the successful deployment of in-situ recovery. This represents a significant
technical validation and a major de-risking milestone for the project.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Figure 4. Field trial location.
This announcement has been authorised for release by the Board of Directors.
Enquiries
For more information please contact:
Andrew Reid
Managing Director
Brazilian Critical Minerals Limited
Andrew.reid@braziliancriticalminerals.com
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Brazilian Critical Minerals Limited (BCM) is a mineral
exploration company listed on the Australian
Securities Exchange.
Its major exploration focus is Brazil, in the Apuí
region, where BCM has discovered a world class Ionic
Adsorbed Clay (IAC) Rare Earth Elements deposit. The
Ema IAC project is contained within the 781 km² of
exploration tenements within the Colider Group and
adjacent sediments.
BCM has defined an indicated and inferred MRE of
943Mt of REE’s with metallurgical recoveries
averaging 68% MREO, representing some of the
highest for these types of deposits anywhere in the
world.
The Company has converted the MRE central portion
from Inferred into the Indicated category with an
extensive drill program during 2024 which has
underpinned the scoping study and economic
analysis released in February 2025.
Ema REE Global Mineral Resource Estimate @COG 500ppm TREO
JORC
cut-off
Tonnes
TREO
NdPr
DyTb
MREO
MREO: TREO
Category
ppm TREO
Mt
ppm
ppm
ppm
ppm
%
Indicated
500
248
759
176
16
192
25
Inferred
500
695
701
165
16
181
26
Total
500
943
716
168
16
184
26
The information in this announcement relates to previously reported exploration results and mineral
resource estimates for the Ema Project released by the Company to ASX on 22 May 2023, 17 July 2023,
19 July 2023, 31 July 2023, 13 Sep 2023, 19 Oct 2023, 06 Dec 2023, 06 Feb 2024, 22 Feb 2024, 13 Mar
2024, 02 Apr 2024, 08 Oct 2024 19 Nov 2024, 21 Jan 2025, 17th Feb 2025, 26th Feb 2025, 10th March
2025, 13th March 2025, 28th April 2025 and 27th May 2025. The Company confirms that is not aware of
any new information or data that materially affects the information included in the above-mentioned
releases.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Competent Person Statement
The information in this announcement that relates to exploration results is based on information
compiled by Mr. Antonio de Castro, BSc (Hons), Member of AusIMM, CREA, who acts as BCM´s Senior
Consulting Geologist through the consultancy firm, ADC Geologia Ltda. Mr. de Castro has sufficient
experience which is relevant to the type of deposit under consideration and to the reporting of
exploration results and analytical and metallurgical test work to qualify as a competent person as
defined in the 2012 Edition of the Joint Ore Reserves Committee (JORC) “Australasian Code for Reporting
of Exploration Results, Mineral Resources and Ore Reserves”. Mr. Castro consents to the report being
issued in the form and context in which it appears.
Appendix 1: Table 1 Ema project – JORC Code (2012 Edition) metallurgical sampling techniques and data.
Item
JORC code explanation
Sampling Techniques
Comments
•
Exploration results are based on solution samples
extracted during ISR field trials conducted by WSP with
support of BCM´s exploration team.
•
Nature and quality of sampling.
•
Include reference to measures taken to ensure sample
representativity and the appropriate calibration of any
measurement tools or systems used.
•
The data presented is based on solution collected from
the monitoring holes after percolation through soils and
saprolite, mined by in-situ techniques.
•
Aspects of the determination of mineralisation
that are Material to the Public Report.
•
Sampling and measurements were supervised by the
Chief Metallurgist and WSP´s hydrogeologist.
•
Sample was extracted from deep wells drilled down to
bedrock basement whereby solution was pumped to the
surface for collection and further analysis
•
Solution samples were tested for pH with a probe called
Incoterm brand pen-type digital pH meter, after
calibration.
•
These results are specific for the tracer test area.
•
All auger holes in the test area were drilled with 6” bit.
•
The deep injection holes in H1 area were the only ones
cased with 2” sliced PVC pipes, all others were cased with
sliced 4” PVC pipes.
•
Coarse gravel sand was inserted between the pipes and
the edges of the holes to create the filter zone.
•
Cement around the collars were built to prevent running
waters from rain to contaminate the underground water.
Drilling
Techniques
•
Drill type (eg core. reverse circulation. openhole hammer. rotary air blast. auger. Bangka.
sonic. etc) and details (eg core diameter. triple
or standard tube. depth of diamond tails. facesampling bit or other type. whether core is
oriented and if so. by what method. etc).
•
Holes drilled are not included in any
Mineral Resource Estimation.
Drill Sample
Recovery
•
Method of recording and assessing core and
chip sample recoveries and results assessed.
•
Measures taken to maximise sample recovery
and ensure representative nature of the
samples.
•
n/a.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Item
Logging
SubSampling
Techniques
and
Sampling
Procedures
Quality of
Assay Data
and
Laboratory
Tests
Verification
of Sampling
and Assaying
JORC code explanation
•
Whether a relationship exists between sample
recovery and grade and whether sample bias
may have occurred due to preferential loss/gain
of fine/coarse material.
•
Whether core and chip samples have been
geologically and geotechnically logged to a level
of detail to support appropriate Mineral
Resource estimation. mining studies and
metallurgical studies.
•
Whether logging is qualitative or quantitative in
nature. Core (or costean. channel. etc)
photography.
•
The total length and percentage of the relevant
intersections logged.
•
If core. whether cut or sawn and whether
quarter. half or all core taken.
•
If non-core. whether riffled. tube sampled.
rotary split. etc and whether sampled wet or
dry.
•
For all sample types. the nature. quality and
appropriateness of the sample preparation
technique.
•
Quality control procedures adopted for all subsampling stages to maximise representativity of
samples.
•
Measures taken to ensure that the sampling is
representative of the in-situ material collected.
including for instance results for field
duplicate/second-half sampling.
•
Whether sample sizes are appropriate to the
grain size of the material being sampled.
•
The nature. quality and appropriateness of the
assaying and laboratory procedures used and
whether the technique is considered partial or
total.
•
For geophysical tools. spectrometers. handheld
XRF instruments. etc. the parameters used in
determining the analysis including instrument
make and model. reading times. calibrations
factors applied and their derivation. etc.
•
Nature of quality control procedures adopted
(eg standards. blanks. duplicates. external
laboratory checks) and whether acceptable
levels of accuracy (ie lack of bias) and precision
have been established
•
The verification of significant intersections by
either independent or alternative company
personnel.
•
The use of twinned holes.
Comments
•
n/a
•
n/a
•
n/a.
•
n/a
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Item
JORC code explanation
•
Documentation of primary data. data entry
procedures. data verification. data storage
(physical and electronic) protocols.
•
Discuss any adjustment to assay data.
•
Accuracy and quality of surveys used to locate
drill holes (collar and down-hole surveys).
trenches. mine workings and other locations
used in Mineral Resource estimation.
•
Specification of the grid system used.
•
Quality and adequacy of topographic control.
•
Data spacing for reporting of Exploration
Results.
•
Whether the data spacing and distribution is
sufficient to establish the degree of geological
and grade continuity appropriate for the
Mineral Resource and Ore Reserve estimation
procedure(s) and classifications applied.
•
Whether sample compositing has been applied.
Orientation
of Data in
relation to
Geological
Structure
•
Whether the orientation of sampling achieves
unbiased sampling of possible structures and
the extent to which this is known. considering
the deposit type.
•
If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to have
introduced a sampling bias. this should be
assessed and reported if material.
Sample
security
•
Audit or
Reviews
•
Location of
Data Points
Data Spacing
and
Distribution
Comments
•
The UTM WGS84 zone 21S grid datum is used for current
reporting. The drill holes collar coordinates for the holes
reported are currently controlled by hand-held GPS.
•
n/a
•
n/a
The measures taken to ensure sample security.
•
The solution samples sealed in plastic bags were sent
directly to Catalão by airfreight and courier to the
laboratory. The Company has no reason to believe that
sample security poses a material risk to the integrity of
the assay data.
The results of any audits or reviews of sampling
techniques and data.
•
The sampling techniques and data have been reviewed
by the Competent Person and are found to be of industry
standard.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
JORC (2012) Table 1 - Section 2: Reporting of Exploration Results
Criteria
Mineral
Tenement and
Land Tenure
Status
Exploration
done by Other
Parties
Geology
Drill Hole
Information
JORC code explanation
•
Commentary
Type. reference name/number. location
and ownership including agreements or
material issues with third parties such as
joint ventures. partnerships. overriding
royalties. native title interests. historical
sites. wilderness or national park and
environmental settings.
•
The EMA and EMA EAST leases are 100% owned
by BCM with no issues in respect to native title
interests. historical sites. wilderness or national
park and environmental settings.
•
The company is not aware of any impediment to
obtain a licence to operate in the area.
•
The security of the tenure held at the time
of reporting along with any known
impediments to obtaining a licence to
operate in the area.
•
Acknowledgment and appraisal
exploration by other parties.
of
•
No exploration by other parties has been
conducted in the region.
•
Deposit type. geological setting and style of
mineralisation.
•
The REE mineralisation at EMA is contained within
the tropical lateritic weathering profile developed
on top of felsic rocks. rhyolites as per the Chinese
deposits.
•
The REE mineralisation is concentrated in the
weathered profile where it has dissolved from the
primary mineral. such as monazite and xenotime.
then adsorbed on to the neo-forming fine
particles of aluminosilicate clays (e.g. kaolinite.
illite. smectite).
•
This adsorbed iREE is the target for extraction and
production of REO.
•
Auger locations and diagrams are presented in
this announcement.
•
Details are tabulated in the announcement.
•
•
A summary of all information material to
the understanding of the exploration
results including a tabulation of the
following information for all Material drill
holes:
•
easting and northing of the drill
hole collar
•
elevation or RL (Reduced Level –
elevation above sea level in
metres) of the drill hole collar
•
dip and azimuth of the hole
•
down
hole
length
interception depth
•
hole length.
and
If the exclusion of this information is
justified on the basis that the information
is not Material and this exclusion does not
detract from the understanding of the
report. the Competent Person should
clearly explain why this is the case.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Criteria
Data
aggregation
methods
JORC code explanation
•
In reporting Exploration Results. weighting
averaging techniques. maximum and/or
minimum grade truncations (eg. cutting of
high grades) and cut-off grades are usually
Material and should be stated.
Commentary
•
No values of rare earths are report.
•
No metal equivalent values are reported.
•
No values of REE were reported for the auger
samples.
•
Mineralisation orientation is not known at this
stage although assumed to be flat.
•
Where aggregate intercepts incorporate
short lengths of high-grade results and
longer lengths of low-grade results. the
procedure used for such aggregation
should be stated and some typical
examples of such aggregations should be
shown in detail.
•
The assumptions used for any reporting of
metal equivalent values should be clearly
stated.
•
These relationships are particularly
important in the reporting of Exploration
Results.
•
If the geometry of the mineralisation with
respect to the drill hole angle is known. its
nature should be reported.
•
If it is not known and only the down hole
lengths are reported. there should be a
clear statement to this effect (eg ‘down
hole length. true width not known’).
•
Appropriate maps and sections (with
scales) and tabulations of intercepts should
be included for any significant discovery
being reported These should include. but
not be limited to a plan view of drill hole
collar locations and appropriate sectional
views.
•
Maps and tables of the auger holes location and
target location are inserted.
Balanced
reporting
•
Where comprehensive reporting of all
Exploration Results is not practicable.
representative reporting of both low and
high grades and/or widths should be
practiced to avoid misleading reporting of
Exploration Results.
•
No REE grades are reported.
Other
substantive
exploration
data
•
Other exploration data. if meaningful and
material. should be reported including (but
not limited to): geological observations;
geophysical survey results; geochemical
survey results; bulk samples – size and
method of treatment; metallurgical test
results; bulk density. groundwater.
geotechnical and rock characteristics;
potential deleterious or contaminating
substances.
•
No other significant exploration data has been
acquired by the Company.
Relationship
between
mineralization
widths and
intercepted
lengths
Diagrams
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
ASX Announcement
Released 13th June 2025
https://braziliancriticalminerals.com/
Investor Hub: https://braziliancriticalminerals.com/auth/signup
Criteria
Further Work
JORC code explanation
•
•
Commentary
The nature and scale of planned further
work (eg tests for lateral extensions or
depth extensions or large-scale step-out
drilling).
•
Additional metallurgical test
magnesium sulphate leach.
•
Extraction of PLS for stream line precipitation and
impurity removals at ANSTO.
Diagrams clearly highlighting the areas of
possible extensions. including the main
geological interpretations and future
drilling areas. provided this information is
not commercially sensitive.
•
Detail topography survey with LIDAR for mine
planning
•
Geophysics survey, Electro resistivity to define
the saprolite/fresh rock boundary and faults in
the rock.
Brazilian Critical Minerals Ltd (ABN: 82 089 221 634)
AUS: Level 28, 140 St Georges Terrace, Perth WA 6000 T +61 8 6383 7820
BRA: Av Jornalista Riccardo Marinho, 360, Sala 113, Barra da Tijuca, Rio de Janeiro T +55 21 2439 57
work
with
Share your feedback
Discover